
Stripping Runs vs. Spirit Runs
Most flavoured spirits are distilled twice, and the two passes have almost nothing in common. The first is a fast bulk job that turns weak wash into strong liquid called low wines. The second is a slow, careful run where that liquid is separated into fractions and only the best kept. Knowing why the two runs exist — and when you can skip the first — is the biggest step from beginner distilling to deliberate, repeatable results.
Read the Safety guide and the Distillation Techniques guide first. The safety rules — open vapour path, no sealed vessel, no valve between boiler and outlet, never leave a running still unattended — apply to every run here.
The two passes at a glance
A stripping run is a first distillation whose product is destined to be distilled again. Its job is bulk concentration: drive the alcohol out of a large volume of fermented wash and collect it, all together, as a smaller volume of much stronger liquid. Speed is the point. The only cut is the foreshots — the first, most volatile liquid off the still — discarded per the Foreshots guide. The rest goes into one container as low wines.
A spirit run is any distillation whose product is kept for drinking. It runs slowly, so the fractions arrive in sequence instead of smeared together, and the output is collected in many small jars for smelling, tasting, and choosing. Cuts are made here: foreshots discarded, heads and tails set aside as feints, hearts kept. See the Cuts guide for the full process.
| Stripping run | Spirit run | |
|---|---|---|
| Purpose | Concentrate wash | Refine low wines |
| Charge | Wash, typically 6–12% ABV | Low wines, diluted to 40% ABV or below |
| Speed | As fast as the condenser can cope | Slow — a thin stream |
| Cuts | Foreshots only | Foreshots, heads, hearts, tails |
| Collection | One large container | Many small numbered jars |
| Product | Low wines, roughly 25–40% ABV | Hearts, 60–85% ABV (pot still) |
Double distillation is the standard method for pot-stilled whisky, rum, and brandy: in Scotch malt whisky production, the wash still makes low wines of about 20–25% ABV from a 6–9% ABV wash, and the spirit still turns them into new-make spirit with the heart at roughly 68–72% ABV.
When to strip, and when to go straight to a spirit run
Strip first when flavour and clean cuts matter
For whisky, rum, brandy, and other pot-stilled spirits, stripping first gives three advantages. It concentrates several washes into one spirit run, so the fractions arrive over a longer period and the transitions are easier to recognise. The second distillation leaves more unwanted compounds behind in the boiler, so the spirit is cleaner than a single pass can produce. And it builds a full boiler charge from several fermentations: as a rule of thumb, about three to four strips fill the same boiler for one spirit run.
Go straight to a spirit run when the wash is strong or the still does the work
A single, slow run — sometimes called a "one and done" — makes sense in a few situations. With a strong wash or wine of 12–14% ABV or more, one careful pot-still pass can already reach a respectable strength with good flavour, and a second distillation may not be worth the time and flavour loss. A reflux still is different: its packed column performs many small distillations in one pass, so a neutral spirit can be made in a single run — though many distillers still strip first.
The hybrid: the "1.5" run
Between the two approaches sits the hybrid often called a 1.5 run: strip one or more washes, then charge the boiler for the spirit run with the low wines plus enough fresh wash to fill it. The fresh wash tops up the volume, restores some character, and dilutes the charge at the same time. Whatever the blend, the same safety ceiling applies: the combined charge must stay at or below 40% ABV.
Running the strip
A stripping run is deliberately unglamorous. Charge the boiler with settled wash — leaving yeast sediment behind, since it scorches — and bring it to the boil at full power. Once distillate flows, run as hard as your condenser can handle: a steady stream. If vapour escapes the condenser outlet, or the distillate comes out hot, back the power off. Take the foreshots off at the start — never into the low wines — then collect everything into a single large vessel.
When to stop stripping
How deep you strip is a trade-off between recovery and quality, and home distillers disagree about the best stopping point — treat these figures as a range of common practice, not a single rule. Clawhammer Supply advises collecting until the output falls to about 20% ABV, noting that going lower simply saves more alcohol. Many strip further, to about 5% ABV off the spout, judging by the total collection instead — roughly 30% ABV for maximum flavour, or nearer 40% ABV for a cleaner result. For a first attempt, stopping when the output reaches about 20% ABV is a sensible middle ground. What remains in the boiler — the spent wash, called backset or pot ale — is mostly water, dead yeast, and residue, and is not distilled further.
Handling low wines
Low wines are the strip's product: a cloudy, rough-smelling liquid at roughly 25–40% ABV, not meant to be drunk as it stands.
Collecting and measuring
Collect each strip's low wines into a clean container and measure the strength with an alcoholometer once cooled (see the Alcoholometer guide). Record each batch's volume and strength — you need both to work out the dilution before the spirit run, and the dilution calculator does the arithmetic.
Storing low wines
Low wines keep well — high enough in alcohol to be stable, they can sit for weeks or months while you accumulate enough for a spirit run. Store them in sealed glass or stainless steel containers, labelled with contents, strength, and date, in a cool place away from heat, sparks, and open flame — low wines are flammable. Keep them away from children and pets, and never in containers that once held chemicals or fuel.
Combining batches
Most spirit runs combine low wines from several strips, and the batches need not match: pour them together, stir gently, and measure the combined strength — the average falls between the strongest and weakest batch, weighted by volume. Combine only low wines from the same style of wash — grain with grain, fruit with fruit — and leave out any batch that smells noticeably worse than the rest, such as a scorched strip.
Diluting low wines before the spirit run
Before low wines go back into the boiler, they almost always need water added — for safety and for separation.
Beyond the safety ceiling, the exact dilution is a flavour choice. Around 30% ABV is a common target for pot-stilled whisky and rum: the extra water holds heavier, less desirable compounds in the boiler, and the hearts come off closer to barrel strength. Charging at 35–40% ABV carries more flavour through, good and bad. Diluting far below 30% ABV is rarely helpful: the run takes longer, output strength drops, and flavour thins out. Use clean, chlorine-free water. Dilution changes the volume too — low wines at 45% ABV diluted to 30% ABV grow by half — so check the final volume against your boiler's safe fill level (never past about 80% of capacity), and keep any immersion element covered. The boiler charge planner works out the volumes.
Running the spirit
The spirit run is where patience pays. Charge the boiler with diluted low wines (and any feints you are recycling — see below), heat gently, and settle into a slow, steady take-off once distillate begins. On a pot still, aim for a thin, unbroken stream or a rapid drip; on a reflux still, follow the column's own procedure. Slower take-off means cleaner separation, because each fraction arrives in turn instead of being dragged along with its neighbours.
Collect in small numbered jars — 200–250 mL each — noting each jar's strength and smell. Let the jars air, covered with a cloth, for a day or two before deciding; the harsh notes masking the early jars fade, and the difference between heads and hearts becomes much clearer. The Cuts guide covers recognising each fraction, placing the cuts, and blending. The first distillate off a 30% ABV charge can start as high as 80–85% ABV on a pot still, and a 40% ABV charge near 90% ABV — as a rough rule of thumb, a pot still multiplies the charge strength two and a half to three times at the start of the run. Strength then falls steadily, and the hearts usually land at 60–75% ABV, to be diluted to drinking or barrel strength afterwards.
What carries over in each pass
The two passes sort different things. The strip separates the volatile from the non-volatile: alcohol and lighter flavour compounds go over the still, while water, yeast, solids, and anything that does not vaporise stays behind. The spirit run then sorts the volatile compounds among themselves, by how readily each vaporises.
| Compound group | Stripping run | Spirit run |
|---|---|---|
| Light volatiles — methanol, acetaldehyde, acetone, ethyl acetate | Come over early; mostly into the foreshots | Concentrated in foreshots and heads |
| Ethanol | Nearly all recovered into the low wines | Forms the bulk of the hearts |
| Fruity esters | Carry over readily into the low wines | Spread across the heads–hearts boundary |
| Heavy alcohols and fusel oils | Come over late in the strip | Concentrated in the tails; set aside as feints |
| Non-volatiles — salts, sugars, proteins, yeast residue | Stay in the boiler as backset or pot ale | Already removed on the first pass |
Two consequences follow. First, a strip does not clean up a bad wash — it concentrates it. Off-flavours from a stressed fermentation survive into the low wines, and the best fix is always a clean fermentation in the first place. Second, each pass strips out flavour along with faults — which is why triple-distilled spirits taste lighter, and why makers of full-flavoured rum and whisky often stop at two passes. The number of distillations is a flavour dial, not a quality score.
Feints in brief
Feints are the heads and tails set aside during a spirit run — too harsh or heavy to drink, but still holding worthwhile ethanol. The standard practice is to save and redistill them: added to the next spirit run's charge, or kept in a dedicated feints container until there is enough for a feints-only run. Two rules apply. Foreshots never go into the feints container — they are discarded on every run. And feints are high-strength liquid: measure them, include them in the boiler-charge calculation, and keep the total charge at or below 40% ABV. A feints-only run is run like any other spirit run — slow, with fresh foreshots discarded and fresh cuts made.
Sources
- HomeDistiller forum, "Stripping Run Spirit Run Definition" — fast strips collecting low wines into one vessel, usually until output is around 5% ABV; the 40% ABV ceiling; 3–4 strips per spirit run; the "1.5" method. homedistiller.org
- Clawhammer Supply, "How to Make 'Sugar Shine'" — fast first pass collecting until output drops to about 20% ABV; slow second pass where cuts are made; the 40% ABV charge ceiling. clawhammersupply.com
- HomeDistiller forum, "Spirit run abv question" — pot-still gain of roughly 2.5–3 times at the start of a run; a 30% ABV charge starting near 80–85% ABV; stripping to 30% ABV keeps more flavour. homedistiller.org
- HomeDistiller forum, "Pot Still and ABV%" — double distillation reaching roughly 70–75% ABV from a low-wines charge around 30% ABV; charges kept below 40% ABV for safety. homedistiller.org
- HomeDistiller forum, "Max ABV of low wines" — 40% ABV the highest recommended boiler charge; 25–30% ABV common for pot-stilled whiskies. homedistiller.org
- HomeDistiller wiki, "Cuts and fractions" — foreshots never recycled; heads and tails saved as feints; tails rich in fusel oils. homedistiller.org
- Ninefold Distillery, "The process of making our award winning Scottish rums" — low wines of about 27–30% ABV at roughly a third of the starting volume; 2–3 strips combined per spirit run. ninefolddistillery.com
- Whiskipedia, "Double distillation" — wash at 7–10% ABV to low wines of 20–30% ABV; heart of roughly 68–72% ABV; feints recycled into the next spirit run. whiskipedia.com
- Arran Whisky, "Guide to whisky distillation" — wash still to low wines of 20–30% ABV; spirit still collecting new-make at 60–75% ABV. arranwhisky.com
- HomeDistiller forum, "some distillation/cuts theory" — Scotch low wines of 20–25% ABV from 6–9% ABV wash; foreshots and feints mixed with low wines for the spirit distillation. homedistiller.org
- Distillery King, "Understanding Heads, Hearts and Tails: Making Perfect Cuts" — heads and tails saved in a feints jar and redistilled when full; foreshots always discarded, never added to feints. distilleryking.com.au