Hydrometer & Alcoholmeter Temperature Corrections
A hydrometer only tells the truth at one temperature — the temperature it was calibrated at. Take a reading anywhere else and the number on the scale is off, sometimes by a lot. These tables bring it back.
Both instruments work the same way: a weighted glass float sinks into the liquid until the weight of the liquid it pushes aside balances its own weight. How far it sinks depends on the liquid's density, and density depends on temperature — warm liquid is thinner and lets the float sink deeper; cold liquid is denser and holds it higher. So a spirit measured warm reads stronger than it really is, and a wash measured warm reads a lower gravity than it really has. The error is not a flaw in the instrument; the scale was simply drawn for one temperature, and every other temperature needs a correction.
Alcoholmeters are calibrated at 20 °C, and the first table below is built for that standard. Sugar hydrometers are a mixed picture: the traditional calibration is 60 °F (15.6 °C), but many newer instruments are calibrated at 20 °C instead — check the paper scale inside the stem, which states the calibration temperature. The second table is written for the 60 °F standard, with the adjustment for 20 °C instruments explained alongside it.
For readings between the grid points, interpolate between the neighbouring rows or columns — or use the Temperature Correction tool, which computes the exact value for any reading and temperature. Both tables on this page agree with that tool.
Alcoholmeter correction (calibrated at 20 °C)
Find your observed reading down the left and the sample temperature across the top. The number in the cell is the correction in % ABV points to add to your reading to get the true ABV at 20 °C. Warm samples read high, so their corrections are negative; cold samples read low, so theirs are positive. At 20 °C itself the correction is zero — that is the temperature the scale was drawn for.
Worked example. You float the alcoholmeter in fresh distillate at 30 °C and read 40% ABV. The table gives −4.19 points at 40% and 30 °C, so the true strength is 40 − 4.19 = 35.81% ABV. Proofing that spirit down on the uncorrected 40% figure would have overshot the water by a wide margin.
| Observed ABV | 0 °C | 5 °C | 10 °C | 15 °C | 20 °C | 25 °C | 30 °C | 35 °C | 40 °C |
|---|---|---|---|---|---|---|---|---|---|
| 0% | +3.02 | +2.21 | +1.40 | +0.65 | 0.00 | 0.00 | 0.00 | 0.00 | 0.00 |
| 10% | +4.87 | +3.26 | +2.03 | +1.03 | 0.00 | -0.98 | -2.19 | -3.53 | -4.86 |
| 20% | +8.23 | +5.78 | +3.64 | +1.68 | 0.00 | -1.66 | -3.30 | -4.96 | -6.63 |
| 30% | +8.83 | +6.72 | +4.21 | +2.05 | 0.00 | -2.14 | -4.17 | -6.15 | -8.15 |
| 40% | +8.28 | +6.15 | +4.04 | +2.06 | 0.00 | -2.14 | -4.19 | -6.33 | -8.42 |
| 50% | +7.58 | +5.64 | +3.78 | +1.89 | 0.00 | -1.95 | -3.93 | -5.93 | -7.91 |
| 60% | +7.04 | +5.28 | +3.54 | +1.77 | 0.00 | -1.81 | -3.67 | -5.54 | -7.41 |
| 70% | +6.53 | +4.90 | +3.29 | +1.65 | 0.00 | -1.70 | -3.43 | -5.19 | -6.98 |
| 80% | +5.90 | +4.45 | +2.99 | +1.51 | 0.00 | -1.56 | -3.14 | -4.77 | -6.44 |
| 90% | +4.75 | +3.68 | +2.50 | +1.26 | 0.00 | -1.35 | -2.74 | -4.18 | -5.68 |
| 100% | 0.00 | 0.00 | 0.00 | 0.00 | 0.00 | -0.89 | -1.81 | -2.78 | -3.84 |
Corrections in % ABV points to add to the observed reading. At the very ends of the scale, some cells read 0.00 where no ethanol–water mixture could actually produce that reading at that temperature — the correction is pinned at the end of the scale rather than invented. Values are computed from the OIML R22 density table (see Sources) and match the Temperature Correction tool exactly.
Sugar hydrometer (SG) correction (calibrated at 60 °F / 15.6 °C)
Find the sample temperature and add the correction to your reading. A warm wash reads low (the float sinks deeper in thinner liquid), so warm corrections are positive; a cold wash reads high, so cold corrections are negative. At 60 °F the correction is zero — that is the calibration temperature this table is built for.
Worked example. Your wash reads 1.050 at 85 °F (29.4 °C) on a hydrometer calibrated at 60 °F. The table gives +0.003 at 85 °F, so the corrected gravity is 1.050 + 0.003 = 1.053.
Hydrometers calibrated at 20 °C (68 °F). If your instrument is calibrated at 20 °C rather than 60 °F, the table still works, but you must shift it: subtract the table's value at 68 °F — about +0.0008, interpolated between the 60 °F and 70 °F rows — from the correction at your sample temperature. The same 85 °F reading above would then correct by +0.0030 − 0.0008 = +0.0022 instead of +0.0030, and a reading taken at 70 °F would need only +0.0002, since 70 °F is barely above the 20 °C calibration point. The Temperature Correction tool applies this offset automatically when you select the 20 °C calibration.
| Sample temperature (°F) | Sample temperature (°C) | Correction to add to the SG reading |
|---|---|---|
| 40 | 4.4 | -0.001 |
| 50 | 10 | -0.0007 |
| 60 | 15.6 | 0 |
| 70 | 21 | +0.001 |
| 78 | 25.6 | +0.002 |
| 85 | 29.4 | +0.003 |
| 91 | 32.8 | +0.004 |
| 96 | 35.6 | +0.005 |
| 101 | 38.3 | +0.006 |
| 106 | 41.1 | +0.007 |
| 110 | 43.3 | +0.008 |
| 120 | 48.9 | +0.010 |
For temperatures between the rows, interpolate — the correction changes smoothly with temperature. Above 120 °F the table stops: let the sample cool before measuring rather than extrapolating.
Sources
- Alcoholmeter table: computed from the OIML R22 (1975) ethanol–water density data, via the site's ethanol density data — the same calculation the Temperature Correction tool uses. The density values were cross-checked against Engineering ToolBox and the European Pharmacopoeia alcoholimetric table (OIML R22). ququqem.neocities.org/alcohol-2026/ethanol_density_tables
- SG hydrometer table: “Hydrometer Adjustment for Temperature” from the distiller charts insert supplied with the Moonshiner's Test Kit, reproduced exactly as printed. Original provenance unknown; values match the standard published hydrometer correction tables in shape and magnitude. Treat as approximate, ±0.001 SG.