Recovery / Efficiency Predictor

Before a run starts, the wash already holds a fixed amount of alcohol — and no still hands all of it back. This tool starts from the wash and works forward: how much pure alcohol is in there, how much of it your still recovers at the efficiency you give it, how many litres of spirit that becomes at the strength you collect at, and how much of it lands in the hearts. It also accounts for the rest, so nothing is left unexplained: the alcohol that stays in the boiler, and the alcohol that comes off as foreshots, heads and tails instead of hearts. The figures are planning estimates, built from the same cut ranges as the rest of this site — use them to set expectations for a run, not as a promise of what the still will do.

How much wash goes into the boiler for this run.
Work it out from your starting and finishing gravity readings. Typical wash 8–12%.
Switching still type resets the efficiency and collection strength below to typical values for that still — adjust them to match your own rig.
A pot still in a single pass typically recovers 85–92% of the wash alcohol; 90% is a realistic middle figure.
The share of the recovered alcohol you expect to keep as hearts. Published guidance puts hearts at 25–70% of the collected alcohol; 50% sits in the middle of that range. Cut tighter for a cleaner spirit, wider for more flavour.
Hearts average about 65% ABV off a pot still — higher at the start of the cut, falling towards 60% by the end. Must be above the wash ABV.
Efficiency is the number to calibrate against your own runs.

No published figure fits every still: how far you run into the tails, how much liquid the boiler and column hold back, and how tight your cuts are all move it. If your runs consistently come in under this prediction, lower the efficiency; if they beat it, raise it. And remember that foreshots, heads and tails are not all truly lost — the foreshots are discarded, but heads and tails are usually saved and re-run with a later batch, so their alcohol comes back on a future run day.

Total pure alcohol in the wash—
Alcohol recovered into the collection vessel—
Expected collected spirit volume at collection strength—
Theoretical maximum at this strength (100% recovery)—
Expected hearts volume—
Foreshots to discard (rough range)—
Heads (rough range, 5–30%)—
Tails (rough range, 10–35%)—
Alcohol left in the boiler (not recovered)—
Alcohol in foreshots, heads and tails (not kept as hearts)—

How the numbers are worked out

Everything starts from the pure alcohol in the wash: volume times ABV, so a 25 litre wash at 10% holds 2.50 litres of pure alcohol, and no run can give you more than that. The efficiency figure is the share of that alcohol the still actually recovers into the collection vessel — at 90%, 2.25 litres come across and 0.25 litres stay behind in the boiler or escape as vapour. Dividing the recovered alcohol by the collection strength turns it into a volume of spirit: at 65% ABV those 2.25 litres of alcohol become about 3.46 litres in the jars, and the same arithmetic at 100% efficiency gives the theoretical maximum of 3.85 litres. The hearts are a share of the recovered alcohol — 50% by default, so 1.13 litres of hearts alcohol, or about 1.73 litres of spirit at 65% — and the rest of the recovered alcohol is the foreshots, heads and tails. The three buckets always add up: hearts plus foreshots, heads and tails plus what stays in the boiler equals the alcohol the wash started with.

This predictor sits one step earlier than the Spirit Run Planner and covers different ground from the Pot Still Yield tool, and the three are built to agree. The Spirit Run Planner starts from a charge already in the boiler — usually low wines — and turns the published cut ranges into a run plan with jar counts; this predictor starts from the wash itself, adds an explicit still efficiency, and gives a single expected hearts figure from a hearts share you choose, rather than the full 25–70% range. Feed both tools the same alcohol and the same assumptions and the answers line up: the hearts figure here always falls inside the planner's range. The Pot Still Yield tool works out the volume at the strength of the first drops off the still, taken from the ethanol–water vapour curve — about 55% for a 10% wash — which is a theoretical bound, since the vapour weakens as the run goes on. This predictor instead uses the average collection strength you enter, which is the figure that actually decides how many jars you fill; set the collection strength to the first-drops strength and the two tools give exactly the same collected volume. The foreshots, heads and tails ranges are the same ones the Cuts Estimator publishes — foreshots 2–6 mL per litre of wash, heads 5–30% and tails 10–35% of the recovered alcohol — so those figures match across all three tools for the same wash.

The efficiency defaults come from published guidance rather than guesswork: a pot still in a single pass typically recovers 85–92% of the wash alcohol, and a reflux column can reach 90–96%, with home distillers typically working at 85–90% (DistilCalc). The defaults sit inside those ranges — 90% for a pot still, 95% for a reflux column — and the pot-still figure matches the default the Pot Still Yield tool and the Spirit Run Planner already use. The collection-strength defaults follow the same pattern: 65% for a pot still, matching the Spirit Run Planner, and 90% for a reflux column, inside the 85–95% ABV a well-run reflux still produces in a single pass. A reflux still recovers more and collects stronger because the column re-distils the vapour many times on its way up, squeezing out alcohol a pot still leaves behind — but it also strips out flavour, which is why pot stills still rule for whisky, rum and brandy. Whatever the defaults say, your own still is the authority: run it a few times, compare what you actually collect with what this tool predicted, and move the efficiency until the two agree.

Two things this tool does not do. It does not model how the strength falls during the run — the collection strength is a single average you supply, and if your real average differs, the volumes shift with it. And it does not tell you where to make your cuts: the hearts share is your judgement, the foreshots, heads and tails figures are ranges because the published guides disagree widely, and the real cuts are decided during the run itself, by nose, taste and readings. Treat the prediction as a map of the run before it starts, then let the still and your senses draw the actual boundaries.

Sources: DistilCalc, “Distilling Yield Calculator” — distilcalc.com/distilling-yield/ (pot still 85–92% recovery, reflux 90–96%); Still Brewin’, “How to Build a Still” — stillbrewin.com/guides/still-building (reflux output 85–95% ABV, pot still hearts 40–65% ABV); Essencia Express instructions — essencia.co.nz (reflux collection 90–94% ABV); HomeDistiller, “Cuts and fractions” — homedistiller.org (cut ranges, shared with the Cuts Estimator).

See also: Spirit Run Planner, Pot Still Yield, Cuts Estimator, Strip Run Planner, Pure Alcohol & Bottle Count, Safety.