Heating-Element Sizing Calculator
Picking an element is usually done backwards: the element is bought first, and the heat-up time is whatever it turns out to be. This tool starts from the other end. Tell it how much wash is in the boiler, where the temperature starts and where it needs to get to, and how long you are willing to wait, and it works out the element power that gets you there — then the current that power draws at your supply voltage, the breaker that current needs, and whether an ordinary household circuit can carry it at all. It is the reverse of the heating-time calculator, and the two agree: feed this tool's answer into that one and the time comes back as the time you asked for. The figures below it show how long the same heat-up would take on two elements you can actually buy, so the answer can be checked against something concrete.
How the numbers are worked out
The energy comes first, and it is the same sum the heating-time tool uses: the wash mass, from its volume and water's density at 20 °C (0.9982 kg per litre), times water's specific heat (4.186 kJ per kilogram per degree) times the temperature rise from start to target. Dividing that energy by the time you want, with the heat-loss allowance taken off the power first, gives the element size: power equals energy divided by time times one minus the loss. A shorter deadline or a bigger loss allowance both push the answer up, in direct proportion.
Treating the wash as water is deliberate, and the direction of the error is the safe one. A real wash weighs a little less per litre than water does, and alcohol takes less heat per degree than water, so the true energy is slightly lower than the figure here — a few percent for an ordinary wash, more for a strong charge such as low wines. That means the element this tool asks for is slightly larger than the bare minimum, and the real heat-up will run a little faster than the time you entered. The heating-time tool makes the same approximation, which is what keeps the two tools in agreement.
The electrical side follows from the power. Current is watts divided by volts, so the same element pulls twice the amps on a 120 V supply as on a 240 V one. A still element runs near full draw for hours, which makes it a continuous load, and a continuous load is only allowed to use four-fifths of its breaker's rating — put the other way, the breaker has to be rated at 125% of the load. A 22.9 A element therefore needs a breaker of at least 28.6 A, which rounds up to the next standard size, 30 A, on 10 AWG copper wire. The tool never rounds down: a load that needs even a fraction over a breaker size steps up to the next one. The breaker sizes it uses are the standard ones from the heating-and-control guide — 15, 20, 30, 40, 50 and 60 A — and the wire sizes are that guide's copper pairings for short runs. A long cable run or a stricter local code may demand thicker wire, which is one more reason the fixed wiring belongs to an electrician.
The two check rows at the bottom run the same energy figure back through the heating-time relation at the wattages of elements that are actually on the shelves: 1,500 W is the usual 120 V size, and 5,500 W the usual 240 V size, both sold as screw-in water-heater elements in ultra-low watt density form. If the answer above sits close to one of those sizes, the check row shows what heat-up time that element really gives, which is often the deciding factor. One trap to avoid: an element only delivers its rated power at its rated voltage. A 5,500 W element built for 240 V gives just a quarter of that — about 1,375 W — on a 120 V supply, because power falls with the square of the voltage, so the 5,500 W check row assumes a proper 240 V circuit.
As with the heating-time tool, the heat-loss allowance is the least certain number in the whole calculation. There is no published value that fits every boiler: lagging, boiler size, room temperature and draughts all move it, and the 20% default is a middle-of-the-road allowance shared with the heating-time tool, not a measured figure. When your own heat-ups keep overshooting the times here, raise the allowance; when they come in under, lower it. And remember that this tool sizes the element for heat-up only — the power that suits a gentle spirit run is much lower, which is why most electric rigs pair a large element with a controller that can turn it down once boiling starts.