
Stuck Fermentations: Diagnosis and Fixes
A stuck fermentation is one that stops before the yeast has finished the sugar — the gravity stops falling while it is still well above the expected final gravity, and the wash stays sweet. Most stuck ferments can be rescued, but only if you find the cause first: adding more yeast to a wash that is too cold, too acidic, or starved of nutrients just wastes good yeast.
First, confirm it is actually stuck
A quiet airlock proves nothing — CO2 escapes through the path of least resistance, and a slow ferment can be nearly silent. The only reliable test is the hydrometer. Take a reading, wait 48–72 hours, and take another at the same temperature. If the two readings match and the gravity is still well above the final gravity your yeast and recipe should reach, the ferment is stuck. If the gravity is still falling, even slowly, it is not stuck — it is slow, and patience is the fix.
Also check that your expectation is realistic. A wash with a high proportion of unfermentable material will finish at a higher gravity than a clean sugar wash — a “high FG” is not always a yeast failure.
The usual causes
Temperature
The most common cause, and the easiest to fix. Most ale and distiller's yeasts work best around 18–30 °C (64–86 °F); below about 12 °C most strains slow to a crawl, and above about 32–35 °C they begin dying. The classic pattern is a wash that starts warm, then chills overnight, and the yeast drops out early. Measure the temperature of the liquid, not the air — the two can differ by several degrees.
Nutrient deficiency
Yeast needs more than sugar: nitrogen, vitamins, and minerals to build cells and enzymes. Sugar washes are nutritionally almost empty, which is why they are the most likely to stall. A wash short on yeast-assimilable nitrogen (YAN) often shows a sulphur or rotten-egg smell. Fruit and grain washes carry more nutrients naturally, but a heavy adjunct load or a skipped nutrient addition can still leave them short.
pH crash
As yeast ferments, it produces organic acids, and the pH of the wash falls. In a sugar wash with no buffering (no grain husks, no minerals), the pH can crash below 3.0, at which point the yeast stops working even though sugar remains. A pH crash is a classic cause of stalls in tomato-paste and plain sugar washes, and it is easy to miss if you never measure pH.
Yeast health and pitch rate
Old yeast, yeast stored warm, or yeast pitched into a wash that was too hot may simply be too weak or too few to finish the job. Under-pitching a high-gravity wash is a common version of this: the yeast colony is too small for the sugar load, the cells age and die before the sugar is gone, and the ferment stalls.
Alcohol tolerance reached
Sometimes the ferment is not stuck at all — the yeast has simply hit its alcohol limit. If your wash is at 15% ABV and your yeast tolerates 14%, no fix will restart it: the yeast is done. Check the yeast's stated tolerance against the ABV implied by your gravity readings (see Fermentation Yields) before trying anything else.
Osmotic shock and inhibitors
A very high starting gravity (above about 1.100 SG) can dehydrate yeast cells before they adapt, causing a delayed start and an early stall. Sanitiser residues, chlorine in the water, or wild microbes can also suppress fermentation.
Diagnosis: find the cause before you act
Work through this checklist in order:
- Gravity: confirmed stable over 48–72 hours, still high?
- Temperature: is the liquid inside the yeast's stated range?
- ABV so far: have you already reached the yeast's tolerance? (Calculate from OG and current gravity.)
- pH: is it below about 3.2? (Test strips or a meter.)
- Nutrients: is this a plain sugar wash with no nutrient added?
- Smell: sulphur or rotten egg suggests nutrient stress; vinegar suggests bacterial contamination.
- Yeast: was it old, stored warm, or pitched into hot wash?
The fix, in order
Fix in this order — least invasive first. Wait 24–48 hours after each step before moving to the next, and check the gravity each time.
- Warm it into range. Move the fermenter somewhere warmer, or use a heating belt or pad, raising the temperature slowly into the yeast's stated range. Avoid sudden heat spikes. This alone rescues many stalls.
- Rouse the yeast gently. Swirl or rock the fermenter just enough to lift settled yeast back into suspension. Keep the lid on — do not splash, whip, or stir air in. Adding oxygen late in fermentation (after about half the sugar is gone) is counterproductive.
- Correct the pH if it has crashed. If the pH is below about 3.2, add a small amount of calcium carbonate (chalk) to bring it back toward 4.0–4.5, stirring gently. Add a little at a time and re-test.
- Add nutrient if the wash was lean. A yeast nutrient (or diammonium phosphate, DAP) can help if the recipe was heavy on sugar and light on nutrients. Follow the product's dosing — over-dosing DAP can raise pH and encourage hydrogen sulphide (rotten-egg) production.
- Re-pitch with a healthy, acclimatised yeast. If nothing else works, make a yeast starter with a robust, alcohol-tolerant strain, and acclimatise it before pitching: over a few hours, add small amounts of the stuck wash to the starter so the yeast adapts to the alcohol and acidity, then pitch the whole starter. Pitching fresh yeast straight into a high-alcohol, low-pH wash often kills it on arrival.
If the ferment still will not move after all of this, the practical answer for a distiller is to run the wash as it is and accept the lower yield, rather than keep fighting it.
Preventing the next one
- Control temperature from pitch to finish — a stable temperature inside the yeast's range is the single best prevention.
- Feed the yeast. Add yeast nutrient to sugar washes, and consider staggered additions for high-gravity washes.
- Don't over-sugar. Plan the wash to finish 1–2% ABV below the yeast's tolerance (see Fermentation Yields).
- Pitch enough healthy yeast — use a yeast starter for liquid yeast and high-gravity washes, and rehydrate dry yeast as the packet directs.
- Buffer sugar washes against pH crash — a little calcium carbonate at the start, or a recipe with some buffering built in (such as a tomato-paste wash), goes a long way.
Sources
- Learning to Homebrew, “How Do You Reset a Stuck Fermentation When Homebrewing Beer?” — confirm with matching gravity readings over 48–72 hours; warm into range, rouse without aerating, nutrient if lean, re-pitch; do not add oxygen after about 50% attenuation. learningtohomebrew.com
- Still Brewin', “Yeast Guide” — alcohol tolerance by yeast type; temperature ranges by strain. stillbrewin.com
- Winemaking Laboratory, “Yeast: biology and selection” — S. cerevisiae alcohol tolerance 14–16% (up to 18% by strain); nitrogen demand and nutrient needs. wine.earth.ge
- Fresh Beer Kits, “How to use a hydrometer” — stable readings over 2–3 days confirm fermentation is finished. freshbeerkits.com