
Still Accessories
A still needs only four things to work — a boiler, a vapour path, a condenser, and a jar — but a handful of accessories can change what it produces and how much you learn from each run. A thumper adds a second distillation in a single pass; a parrot reads the proof as the spirit flows; a gin basket turns a pot still into a flavour still; a well-placed thermometer tells you what is coming over. This intermediate guide covers each one: what it does, what it adds, and the safety rules that apply to all of them.
Thumpers and doublers
A thumper — also called a thump keg, thump barrel, or doubler — is a small vessel that sits between the boiler and the condenser, partly filled with liquid: water, wash, low wines, or tails from an earlier run. Hot vapour from the boiler enters through a pipe that reaches down into the liquid. The vapour bubbles through, condenses, and gives up its heat; the liquid in the thumper warms, comes to the boil, and re-vaporises — so the spirit is effectively distilled a second time without a second run. The name comes from the sound: as vapour bursts through the liquid in the keg, it makes a rhythmic thumping noise that gave the device its folk name.
What a thumper adds is proof and purity in a single pass. A pot still with a thumper produces spirit at a higher strength than the same still without one — roughly what you would get from running the low wines through the still a second time — and the extra distillation strips out some of the heavier, rougher compounds. It does not literally double the purity, despite the nickname "doubler": it raises it, in one run, at the cost of extra joints and extra liquid to manage. A thumper should generally be about 25–40% of the size of the main boiler — big enough to hold a useful charge of liquid and to give the vapour time in it, small enough that the boiler's vapour can bring it to the boil.
Strictly speaking, a thumper and a doubler are not the same device, though the terms are used interchangeably in hobby circles. A true doubler accepts condensed liquid from a first condenser and is heated separately — by a steam coil or an external heat source — to re-boil it, which gives the distiller more control over temperature and therefore over proof. A thumper accepts vapour directly, is heated only by that vapour, and gives the distiller less control but needs no second condenser and no second heat source. For a home still, the thumper is the practical version.
The safety rules for a thumper follow from its position in the vapour path. The inlet pipe must reach below the liquid surface, or the vapour will simply pass over the top and the thumper does nothing. The thumper must never be filled so full that liquid can be carried over into the condenser, and the outlet from the thumper to the condenser must stay open and unobstructed — a flooded or blocked thumper chokes the vapour path, and a choked vapour path builds pressure. Fill it to roughly half, confirm the vapour route is unobstructed before each run, and treat a thumper that has suddenly gone quiet while the boiler is still boiling as a warning sign worth investigating from a safe distance with the heat off.
Parrots: live proof readings
A parrot — a proofing parrot — is a small chamber, usually copper or stainless steel, that holds an alcoholmeter in the output stream. Distillate flows in from the condenser, fills the chamber around the floating alcoholmeter, and overflows out to the collection vessel. The result is a continuous, live reading of the spirit's strength as it comes off the still, which makes it much easier to see the transitions between fractions: the proof falls steadily through a run, and the parrot shows that fall in real time instead of requiring a sample to be drawn and tested jar by jar.
That convenience comes with one absolute safety condition, and it is the reason parrots are controversial in some distilling circles: a parrot must never seal the condenser outlet. A still must always vent freely to the open air, and any fitting that closes the vapour path can turn the boiler into a bomb. A parrot is safe only when the vapour path stays open past it. In practice that means three things. First, the parrot's vent must stay uncovered: commercial parrots have a ventilation hole in the collection cone, and the condenser outlet tube must not be pushed down so far that it covers it. Second, the parrot's own outlet pipe must never be submerged in the collected distillate — the manufacturer's instructions warn explicitly that a submerged outlet can cause the boiler to implode as it cools, and you should always be able to see the drops of distillate falling freely into the collection vessel. Third, the parrot must sit below the condenser outlet with an air gap or a vented connection, never as a sealed, airtight coupling. If your parrot setup cannot meet those three conditions, do not use it — test each jar with an alcoholmeter after collection instead, which gives the same information a few minutes later and carries no risk at all.
One more practical note: a parrot reads the proof of the spirit passing through it at that moment, and alcoholmeters are calibrated for a specific temperature (usually 20 °C). Distillate straight off the condenser is often warmer than that, so a parrot reading taken on warm spirit will read low until the spirit cools. Treat the parrot as a guide to trends and transitions, and confirm the final proof of your kept spirit with a cooled sample and a temperature correction.
Gin baskets and vapour infusion
A gin basket is a perforated chamber — usually stainless steel or copper — that sits in the vapour path between the boiler and the condenser and holds botanicals: juniper, coriander, citrus peel, and whatever else the recipe calls for. As hot alcohol vapour rises through the basket, it passes over and through the botanicals, picks up their volatile oils and aromas, and carries them on into the condenser. The technique is called vapour infusion, and it is one of the two classic ways to make gin — the other being steep-and-boil, where the botanicals soak in the spirit in the pot itself.
Vapour infusion has a distinct character. Because the botanicals never sit in boiling liquid, the more delicate aromatics — floral notes, fresh citrus, herbs that would turn bitter or muddy if stewed — survive the process better, and the resulting gin tends to be brighter and lighter than a steeped one. The two methods are often combined: robust roots and spices steeped in the pot, fragile flowers and peels in the basket. A common starting point for dosing is roughly 80–120 g of botanicals per 10 L of spirit, though the right amount depends on the recipe and the botanicals themselves, and the balance between juniper and the rest is a matter of taste and experiment. Our gin guide covers the recipes and the botanical bills in full.
There are two common basket designs. An inline basket sits directly above the boiler, in the riser or column, so all the vapour passes through it. An offset basket sits to the side of the column, sometimes with a drain valve at the bottom so that condensed oils can be collected separately. Whichever design you use, the basket must not obstruct the vapour path: pack the botanicals loosely, never use powdered botanicals or oils that can clog the perforations, and leave the vapour a free route through. A basket packed solid with fine material is a blockage waiting to happen, and a blocked vapour path is the one failure this guide keeps coming back to. Empty and clean the basket after every run — spent botanicals left in place go stale and taint the next batch.
Thermometers: placement and types
A thermometer is the cheapest instrument on a still and one of the most argued about. It cannot choose your cut points — only smell and taste can do that — but it can tell you what is coming over, how the run is progressing, and when the tails are arriving, and it is invaluable for keeping notes that make the next run predictable.
Where to put it
The most useful thermometer sits high in the vapour stream, at the head of the still just before the vapour turns toward the condenser. That temperature tracks what is coming over: it climbs gradually from the first drip to the last as the lighter fractions are exhausted and heavier ones take over, and a vapour temperature climbing well past ethanol's boiling point of 78.4 °C at sea level signals the tails are arriving. The thermometer bulb should sit in the vapour stream itself, just below the point where the vapour turns toward the condenser — too low and it reads heat conducted from the boiler, too high and it reads vapour that has already begun to cool and condense.
A second thermometer in the boiler, below the liquid line, is less useful for making cuts but earns its place in other ways: it tells you how the wash is heating, it is essential if you heat mash water or run a mash in the boiler and need to hit specific temperatures, and it shows when the boiler charge is nearly spent. Many distillers run both — one in the vapour path, one in the boiler — and record both against each jar.
Analogue vs digital
Analogue dial thermometers are simple, need no power, and are easy to read at a glance, but they are slow to respond and their accuracy depends on calibration — a cheap dial thermometer can be several degrees out, and you would never know unless you checked it against boiling water. Digital thermometers, usually built around a thermocouple or a resistance probe, respond faster, read to a tenth of a degree, and often log data or sound an alarm at a set temperature. The most common type in hobby stills is the K-type thermocouple: a thin, flexible probe that fits through a small compression fitting in the riser or head, sealed with PTFE tape, and reads into a handheld meter or a panel display. K-type probes are inexpensive, widely available, and accurate enough for distilling — typically within about a degree — and a multi-channel meter lets you watch boiler, head, and parrot temperatures at once. Whichever type you choose, check it against boiling water (100 °C at sea level, adjusted for your altitude) before trusting it, and remember that a thermometer is a reference instrument: record what it says, but make your cuts by smell and taste.
Collection vessels and the numbered-jar method
What you collect spirit into matters as much as what you distil it in. The rule is simple: glass and stainless steel only. High-proof spirit is a solvent, and it will pull chemicals out of plastic, leach flavours from rubber, and dissolve adhesives. Plastic containers — even food-grade ones — have no place holding spirit above a few percent ABV, and neither do mystery metals, painted vessels, or anything with a plastic lining. Mason jars and other glass jars are the standard for a reason: they are inert, they are cheap, they seal well, and you can see what is in them. Stainless steel is equally safe and better for larger volumes, such as low wines from a stripping run.
For a spirit run, collect in many small, numbered jars rather than one big vessel — the numbered-jar method. Jars of roughly 250–500 mL, numbered in run order, each labelled with its time, vapour temperature, and ABV, let you judge every fraction the next day with a fresh nose instead of making irreversible decisions in the moment. Our cuts guide covers the method in full, including the overnight rest under a loose cover and how to sort the jars into hearts and feints the next day.
Two safety points close the subject. First, the collection vessel must never seal the condenser outlet: the outlet pipe must drip freely into an open vessel, never be submerged in the collected spirit, and never be connected to a sealed container. A submerged outlet can create a vacuum as the boiler cools and draw spirit back into the still, or worse. Second, keep the collection vessels away from the heat source and any open flame, on a stable surface where they cannot be knocked over, and label every jar the moment it is filled — heads and hearts are indistinguishable by sight alone, and an unlabelled jar is a jar you cannot trust.
Sources
- Whisky Advocate, “What a Doubler and Thumper Mean For Whiskey Making” — a thumper is a small vessel between still and condenser, pre-filled with liquid, in which vapour condenses and re-vaporises for a second distillation; a doubler takes liquid and is heated separately, giving more control over temperature and proof. whiskyadvocate.com
- HomeBrew Academy, “The Thumper Keg Explained” — a thumper should generally be about 25–40% of the size of the main boiler; it distils the output a second time in a single pass, raising proof without a second run. homebrewacademy.com
- Brewhaus, “Where Do I Attach This Thumper?” — a thumper increases purity in one pass but does not literally double it; vapour enters the liquid, heats it, and lower-boiling compounds vaporise out. brewhaus.com
- Still Brewin', “Making Cuts” — “NEVER seal a still. A sealed still is a bomb. There must always be an open path for vapor to escape through the condenser”; a parrot holds a hydrometer in the output stream for a real-time ABV reading; thermometer placement high in the vapour stream at the head of the still; collection in 10–20 small numbered glass jars. stillbrewin.com
- Still Spirits, “Parrot Head Instructions” — the distillate outlet pipe must never be submerged in distillate, “otherwise, the boiler may implode”; the condenser outlet tube must not be pushed down so far that it covers the parrot's ventilation hole. shop.greatfermentations.com
- Samovar Tool (2022), “Safety Rules for Distillation and Rectification” — do not plug the condenser outlet or submerge the outlet tube in liquid unless the design provides for it; the receiving vessel must not turn the take-off line into a closed system. samovar-tool.ru
- HomeDistiller, “New Distiller's FAQ” (wiki) — all stills must be open to atmosphere and never allow pressure to build; do not use plastics in the vapour path. homedistiller.org
- DIY Distilling, “How Does A Gin Basket Work” — a gin basket holds botanicals in the vapour path so vapours extract flavours on the way to the condenser; inline and offset types; roughly 80–120 g of botanicals per 10 L of spirit. diydistilling.com
- Difford's Guide, “How Gin Is Made: Distillation Methods Explained” — in vapour infusion the botanicals do not contact liquid spirit at all; they sit in baskets and encounter only the spirit as vapour. diffordsguide.com
- Everglow Spirits, “Botanical Baskets: The magic of the vapour chamber” — vapour infusion protects delicate botanicals that would degrade in hot liquid; steeping gives a bolder profile, vapour infusion a gentler, more aromatic one. everglowspirits.com
- Home Distiller forum, “What's the best way to connect thermometer to your column?” — K-type thermocouple probes fitted with a compression fitting and PTFE tape; thermometers mounted in the riser below the elbow. homedistiller.org
- Home Distiller forum, “Placement of thermometer on a pot still” — highest point in the vapour path correlates vapour temperature to distillate ABV; a boiler probe is useful for mashing temperatures; cuts are made by smell and taste, not temperature. homedistiller.org
- Labster, “The distilling head with thermometer” — the thermometer bulb should sit just below the point where the side arm stretches out to the condenser; too low reads too warm, too high reads too cold. theory.labster.com