
Cleaning Runs & Still Maintenance
A still is a food-processing machine that runs at boiling point, and it needs to be treated like one. A new still arrives full of construction residues that must be cleaned out before it ever makes drinkable spirit, and every run after that leaves deposits that will taint the next batch if you let them build up. The good news: routine cleaning takes about ten minutes, and the deep cleans are simple chemistry you can do with vinegar and citric acid.
Cleaning a new still before first use
Whether you built your still or bought it, the inside of the metal is not clean. Soldering and welding leave flux, oxides, and scale; manufacturing leaves oils and dust; and copper oxidises in storage. None of that belongs in your spirit. The standard cleaning sequence, used by the HomeDistiller community for years, has three stages, and the reason for three is that different residues dissolve in different things: some come off in water, some in acid, and some only in alcohol. All three stages are needed.
- Soak and scrub. Start by cleaning every part you can reach by hand. Wipe down solder joints and welds with a rag or sponge to remove as much visible residue as possible, and soak small parts in dilute vinegar for a few hours or overnight. This is also the time to check every joint for leaks and every fitting for tightness.
- Water or steam run (optional but recommended). Charge the boiler roughly three-quarters full of water, assemble the still, and bring it to a boil with the cooling water off, letting steam blow through the condenser for 15–20 minutes. This flushes loose debris and confirms that steam can pass freely through the whole vapour path. Then switch the cooling water on and keep it running for up to an hour.
- Vinegar run. Charge the boiler about half full with a 50/50 mixture of white vinegar and water, and run it as you would a distillation. Start with the condenser off for 15–20 minutes so acidic steam reaches every part of the vapour path — including the top of the condenser, which normal condensing operation may never touch — then turn the cooling on and run for 20–30 minutes after distillate starts coming over. The smell is strong, so ventilate well. Afterwards, discard the vinegar charge and rinse everything thoroughly with clean water.
Use the vinegar run to learn your still: it is the perfect low-stakes chance to check for leaks at every joint, confirm the condenser knocks down all the vapour, and get a feel for how your heat source responds — with no flammable alcohol involved.
The sacrificial run — and why it is discarded
After the vinegar run comes the alcohol run: ferment something cheap — a tomato-paste sugar wash is the usual choice, since it costs almost nothing — and run it through the still as if it were a real spirit run, collecting all the distillate down to about 20 proof (10% ABV). Then throw all of it away. Every drop. No exceptions, no tasting, no keeping it “for cleaning,” and no saving the leftover liquid in the boiler either.
The reason is straightforward: alcohol dissolves things that water and vinegar do not. The first alcohol through a new still picks up the last traces of flux, manufacturing oils, and metal oxides that the earlier stages missed, along with residual vinegar. That distillate is contaminated by design — it did its job by collecting the contamination, and drinking it would put those residues in your body instead of down the drain. It will also taste foul, which is your nose confirming what the chemistry says.
Once the sacrificial run is done and everything has been rinsed with water and allowed to drain dry, the still is ready for its first real run. If you are ever unsure whether a still is clean — after a long idle period, after a repair, after buying second-hand — repeat the sequence. It is cheap, and “it ain't clean until it is clean” is a good rule to live by.
Cleaning after each run
Routine cleaning after a run is quick, and doing it while everything is still warm makes it quicker. The heat and alcohol of the run itself do much of the sanitising for you; your job is to remove the deposits before they harden or go stale.
- Boiler: drain the spent wash (the backset) while it is warm, rinse with hot water, and wipe out any solids. For grain mashes, a soft brush and a little mild dish soap will shift the residue; rinse well afterwards so no soap survives into the next run.
- Head, riser, and column: rinse with hot water and let them drain. If you use copper mesh or other packing, rinse it too — it collects sulfur compounds and residues, and a quick rinse keeps it working.
- Condenser: flush with hot water in the direction the vapour travels, then let it drain fully. See the condenser section below for more.
- Outside: wipe down with a damp cloth. Copper will darken with heat and handling; that is cosmetic, and the polishing section below covers it if you care about the shine.
Do not put parts away wet, and do not seal a damp still in a bag or box. Trapped moisture is what grows mould and corrodes copper between runs. Let everything air-dry completely — standing parts on end so water drains out — before storing or reassembling.
Descaling and polishing copper
Copper is a working metal, not a decorative one, and a still's copper will change colour with use. A dull brown patina on the outside is harmless. What matters is the inside: mineral scale from hard water, dark oxide films, and — on a still left damp — green crusty corrosion (verdigris), which is a copper salt you do not want in your spirit. A vinegar wipe-down every few runs and a citric acid soak every ten to fifteen runs keeps the metal in good order.
- Diluted vinegar (one part white vinegar to three parts water) is the everyday cleaner for light tarnish and mineral film. Wipe or soak for 10–15 minutes in warm solution, then rinse well with clean water.
- Citric acid is stronger and better for heavier tarnish and green corrosion. Dissolve 1–2 tablespoons per quart of warm water (or per gallon for a gentler soak), submerge the parts or fill the boiler, and leave for 15–20 minutes before scrubbing gently with a soft brush and rinsing thoroughly. Citric acid is food-grade and effective, but do not leave copper soaking in it indefinitely — strong acid left too long etches thin copper.
- For the outside shine: the same citric acid solution applied with a soft cloth, rubbed gently and rinsed, restores the warm copper colour. Some makers finish with a paste of vinegar and salt, or a dedicated copper polish; whatever you use on the outside, keep it off the inside surfaces that touch spirit, and rinse thoroughly.
Scale from cooling water builds up wherever water flows — inside a Liebig jacket or around a worm coil — and it insulates the metal, slowly reducing how well the condenser transfers heat. If your condenser seems less effective than it used to be, a citric acid soak of the water side is the usual fix. Using soft or distilled water for cooling, where practical, slows scale formation in the first place.
Condenser care
The condenser is the one part of the still whose failure is immediately dangerous: if it stops knocking down vapour, hot flammable alcohol vapour escapes into the room. Its maintenance deserves more attention than any other component.
- Flush after every run. Hot water through the vapour side, in the direction of vapour flow, removes the residues of the run. A diluted-vinegar fill for 10–15 minutes, then a rinse, deals with light scale.
- Check the water side too. Cooling hoses clog, kink, and grow biofilm. Flush the cooling circuit regularly, check hoses for cracks and softening, and make sure fittings are tight — a cooling-water leak onto a hot boiler is a scalding and electrical hazard.
- Watch for reduced performance. If vapour starts escaping the outlet, or the condenser needs more cooling water than it used to for the same heat input, something has changed: scale, a partial blockage, or a failing water supply. Find the cause before the next run, not during it.
- Store it dry and open. A condenser stored full of water grows biofilm and corrodes; one stored sealed and damp does the same. Drain it fully and leave both ends open to air.
Gaskets, seals, and flour paste
Joints leak, and a leaking joint on a running still vents flammable vapour. Check every seal before each run, and replace anything that is hardened, cracked, compressed flat, or no longer springs back.
- PTFE (Teflon) gaskets are the most widely recommended choice for tri-clamp joints: chemically inert, food-safe, and unaffected by hot alcohol. Their drawback is that PTFE is stiff and can creep under heat, so clamps may need re-tightening once the still is hot.
- Silicone gaskets are flexible, heat-resistant, and widely used in commercial distilling equipment; they are FDA-approved as food-safe. Some hobbyists distrust them on principle, preferring PTFE, but inspectors and manufacturers accept them. Whatever you use, replace gaskets every one to two years as preventative maintenance, whether they look worn or not.
- Flour paste is the traditional seal for pot-still lids and joints without clamps: mix about three parts flour to one part water into a stiff dough, roll it into strips, and press it around the joint before the still heats up. It hardens as the still warms, seals well, and flakes off easily after the run for a fresh application next time. Never use rubber seals, ordinary O-rings, or silicone sealant from a tube in the vapour path — hot ethanol attacks them.
Storing equipment between runs
Most still damage happens between runs, not during them. A still put away damp, dirty, or sealed up will corrode, grow mould, and greet you with green copper and stale smells next time.
- Dry everything completely before storage. Air-dry parts separately, standing them so water drains out, and do not reassemble until all surfaces are dry to the touch.
- Store disassembled or loosely covered in a dry, ventilated place. A cloth cover keeps dust out while letting air circulate; a sealed plastic bag traps moisture and invites corrosion.
- Keep copper bright or accept the patina — but do not leave green corrosion to spread. A quick citric-acid wipe before a long storage period, followed by thorough drying, is worth the ten minutes.
- Store fermenters clean and dry too, with lids loose or off. A sealed damp fermenter is a mould farm.
- Before a run after a long break, inspect everything: check gaskets, run water through the condenser, look inside the boiler and vapour path for corrosion or nests, and if anything looks off, run the vinegar-and-sacrificial sequence again. A still that has sat idle for months earns a fresh cleaning run.
Sources
- HomeDistiller wiki, “Planning your first Run” — vinegar cleaning run with a 50/50 vinegar and water charge, run 20–30 minutes after producing; sacrificial run from a cheap wash such as a Birdwatchers wash, output dumped, not drunk; flour seals of 3 parts flour to 1 part water. homedistiller.org
- HomeDistiller forum, “Cleaning a new still” — soak and scrub in dilute vinegar first; steam the still with the condenser off so acidic steam reaches the top of the condenser; alcohol cleaning run to remove what water and vinegar cannot; never use denatured alcohol. homedistiller.org
- HomeDistiller forum, “Cleaning your new still correctly” — three cleaning runs (water, then 50/50 vinegar and water, then sacrificial alcohol), because different residues dissolve in water, acid, and alcohol; the sacrificial alcohol and the backset are both dumped, no exceptions. homedistiller.org
- StillZ, “How Do You Clean a Copper Still Without Damaging It?” — diluted vinegar (1 part vinegar to 3 parts water) for 10–15 minutes; citric acid 1–2 tablespoons per quart for 15–20 minutes; never bleach or chlorine cleaners on copper, and never mix acids with bleach; vinegar wipe-down every 3–5 runs and citric acid soak every 10–15 runs. blog.stillzstore.com
- BeaCleaner, “How To Clean A Copper Still” — citric acid 1–2 tablespoons per gallon of warm water, heated to about 140 °F (60 °C) for 15–30 minutes; avoid abrasive cleaners and steel wool on copper. beacleaner.com
- StillDragon, “Is Silicone Safe for Distilling?” — replace gaskets every one to two years regardless of material; PTFE gaskets are food-safe but less flexible and can loosen as the still heats; silicone gaskets are flexible, heat-resistant, and FDA-approved. stilldragon.com
- Whiskey Still Pro, “Easy DIY Flour Paste for Your Copper Still” — flour paste of 3 parts flour to 1 part water, rolled into strips and pressed around joints; it hardens as the still heats and flakes off after the run. whiskeystillpro.com